Arduino Cheat Sheet and Pinouts


Arduino Cheat Sheet and Pinouts
images (3).jpg
8-19-2014_9-47-12_AM.jpg
68747470733a2f2f7261776769746875622e636f6d2f426f756e692f41726475696e6f2d50696e6f75742f6d61737465722f41726475696e6f253230556e6f253230523325323050696e6f75742e706e67.png
68747470733a2f2f7261776769746875622e636f6d2f426f756e692f41726475696e6f2d50696e6f75742f6d61737465722f41726475696e6f253230556e6f25323050696e6f75742e706e67.png
uno.jpg
ARDUINO.Mega.Pinout.Diagram.png
Due-pinout-WEB-444x400.png
nano.jpg
ATtiny.png
ATtiny.png
Arduino cheet sheet v02bsmall.png
You can find all the cheat sheets and pinout here.sometimes it really works fine mainly the programming cheat sheets.
You can also download the pdf files from here:

Comments

Post a Comment

Popular posts from this blog

0.96 OLED Display With Arduino & Getting Text From Serial Monitor...

Image
0.96 OLED Display With Arduino & Getting Text From Serial Monitor... Now we start to work with 0.96' OLED Display with arduino and we will try to display text from the serial monitor input... In this tutorial i will show you how to connect and test and write some data from serial monitor to a 0.96" i2c OLED display module to an arduino. Parts: Breadboard and hookup wires Arduino The OLED i2c display The connections from the display: VCC to arduino 5v GND to arduino GND SCL to arduino pin A5 SDA to arduino pin A4 Both libraries below needs to be installed before you are able to continue with this instructable. https://github.com/adafruit/Adafruit_SSD1306 (SSD1306 library) https://github.com/adafruit/Adafruit-GFX-Library (GFX library) Step 2: Correction in Library N Code.. For Adafruit_SSD1306 Library: Go to: C:\Program Files (x86)\Arduino\libraries\Adafruit_SSD1306 Open Adafruit_SSD1306.h (in a text editor like Notepad++ for example...
Read more

Arduino & 4x4 Matrix keypad

Image
                              4x4 Keypad Pinout/Diagram Arduino to Keypad Connection Diagram After connecting as shown here we need to upload a code on our arduino. Here's the  Code : #include <Keypad.h> const byte numRows= 4; //number of rows on the keypad const byte numCols= 4; //number of columns on the keypad char keymap[numRows][numCols]= { {'1', '2', '3', 'A'}, {'4', '5', '6', 'B'}, {'7', '8', '9', 'C'}, {'*', '0', '#', 'D'} }; byte rowPins[numRows] = {9,8,7,6}; //Rows 0 to 3 byte colPins[numCols]= {5,4,3,2}; //Columns 0 to 3 //initializes an instance of the Keypad class Keypad myKeypad= Keypad(makeKeymap(keymap), rowPins, colPins, numRows, numCols); void setup() { Serial.begin(9600); } //If key is pressed, this key is stored in 'keypressed' variable /...
Read more

Home About Contact Using Minim OSD in NAZA

Image
So if you dont wanna break your bank for an iOSD module for you DJI Naza , here are some simple (yet DIY complicated) stuffs to follow. NOTE: TRY AT YOUR OWN RISK (VERY LOW RISK IF YOU FOLLOW THE INSTRUCTIONS PRECISELY WITHOUT ERRORS OR SYNC FAILURE. YET, I AM NOT RESPONSIBLE FOR A FRIED NAZA, THERMONUCLEAR WAR OR YOU NEIGHBORS DEAD CAT DIY project that shall make it possible to connect DJI Naza-M (v1, v1 Lite, v2) with MinimOSD using either: Arduino board (Pro Mini, 16Mhz, 5V) and serial connection (works with DJI Naza-M v1, v1 Lite and v2) Teensy 3.1 board + TeensyDuino (tested with version 1.20) + CAN transciever and CAN connection (works with DJI Naza-M v1 and v2 with PMU, does not work with v1 Lite). I did not test in flight, all the tests were done on the ground. It converts data from Naza GPS/FC data into Mavlink and provides the following information via the MAVLink GPS_RAW_INT, ATTITUDE, VFR_HUD, SYS_STATUS and RC_CHANNELS_RAW messages: latitude longit...
Read more